Skip to main content

Ramsay Electrical Aptitude Test (Form A6) Practice

Ramsay Corporation’s entry-level electrical test for apprentice and trainee applicants: 36 questions in 18 minutes across six areas.

Practise Ramsay Electrical Aptitude Test

Ramsay Electrical Aptitude Test is in the Ramsay Corporation unlock: £15 for all 5 tests, one-time payment, no subscription. Or try Ramsay Mechanical Aptitude Test free first.

Questions
36, four options each (A to D).
Time
18 minutes.
Content areas
Mathematics, Electrical Concepts, Electrical Schematics, Process Flow, Signal Flow and Electrical Sequences.
Order
Questions get harder as the test goes on.
Scoring
Number right. Nothing is taken off for a wrong answer, and a blank scores the same as a wrong answer.
Pass mark
Not published. Each employer sets its own cut score.
Calculator
Not published. Ramsay says it depends on the test, so bring nothing unless told.
Going back
Not published for the online form. On paper you can move around within a timed part.

How the Ramsay Electrical Aptitude Test works

The Electrical Aptitude Test, Form A6, checks whether an applicant can pick up electrical work, not whether they already know it. It has 36 questions in 18 minutes, which is 30 seconds a question, under a proctor on paper or on screen. Form BR is the alternate form, with the same length and clock.

Six areas run through the paper: basic mathematics, electrical concepts such as voltage and current, reading schematics, following a process flow chart, tracing signal lines, and spotting the pattern in a sequence. Ramsay calls the layout a sectional spiral: the areas repeat and the questions get harder as you go, so the last third is the toughest. Ramsay does not publish how many questions come from each area.

Your mark is the number right. Ramsay’s published average for the online form is 23.48 of 36, from 658 candidates, about 65%. Ramsay sets no pass mark; the employer picks its own.

A method for each area

  • Mathematics: solve for the unknown in short equations and use Ohm’s law, V = I × R, in all three arrangements.
  • Concepts: know that cells in series add their voltages, that resistors in series add, and that two equal resistors in parallel give half of one.
  • Schematics: a lamp lights only if there is a complete path from one end of the supply to the other with every switch on that path closed.
  • Process flow: answer each decision in the order the chart asks it, and stop at the first box that ends the chart.
  • Signal flow: follow one line at a time through every crossing with your pencil. Lines cross; they never join.
  • Sequences: name the change from one step to the next, such as one lamp moving right, before you look at the options.

Worked examples

Ohm’s law. A 12 V supply drives a 4 Ω heater. What current flows? (A) 0.33 A (B) 3 A (C) 16 A (D) 48 A. I = V ÷ R = 12 ÷ 4 = 3 A. The answer is B.

Schematic. Two switches, S1 and S2, are in series with one lamp. Which must be closed for the lamp to light? (A) S1 only (B) S2 only (C) Either S1 or S2 (D) Both S1 and S2. In series, the current passes through both switches, so both must be closed. The answer is D. If the switches were in parallel, either one would do.

Sequence. A row of four lamps shows lit, off, off, off; then off, lit, off, off; then off, off, lit, off. What comes next? The lit lamp moves one place right each step, so the next row is off, off, off, lit.

Tips for the real test

  • Bank the early questions quickly. They are the easiest, and the hard ones at the end need the time.
  • Thirty seconds is short for a signal trace. If a tangle is not resolving, mark your best guess and move on.
  • Write V = I × R at the top of your scratch paper before the clock starts.
  • Answer every question before time is called. There is no penalty for a guess.

Practise on CogniPrep

Our practice test gives you 36 questions in 18 minutes, six from each area, running three times through the six areas with each run harder than the last. Circuits, lamp rows, flow charts and line traces are generated fresh each sitting. You can move between questions, flag them and use an answer grid, and your result shows your mark beside Ramsay’s average with the area that cost you most.

Questions candidates ask

How many questions are on the Ramsay electrical test?

36 questions in 18 minutes on Form A6, with four options each. The alternate Form BR has the same length and time.

What is on the Ramsay Electrical Aptitude Test?

Mathematics, electrical concepts, schematics, process flow, signal flow and electrical sequences, with the questions getting harder as the test goes on.

What is the pass mark on a Ramsay test?

Ramsay publishes none. Each employer or apprenticeship committee sets its own cut score, sometimes after a study of its own jobs, so ask the one you applied to what it uses.

Is the Ramsay electrical test the same as ElecTest?

No. ElecTest is a 60-question Ramsay knowledge test for experienced electricians. The Electrical Aptitude Test is for applicants who have not trained yet.

Will I see my Ramsay score?

No. Ramsay sends results to the employer, not to the candidate. The employer decides what to tell you.

Read next

Try it before the real thing

Get used to the Electrical Aptitude Test format with our practice version before you take the real one. It is part of the Ramsay Corporation unlock.

Practise Ramsay Electrical Aptitude Test